CT 281 - Energia solare

00312006

ENV 12977-1:2001

Thermal solar systems and components - Custom built systems - General requirements

This European Prestandard specifies requirements on durability, reliability and safety of small and large custom built solar heating systems with liquid heat transfer medium for residential buildings and similar applications. The Prestandard contains also requirements on the design process of large custom built systems.

Non prevista

00312007

ENV 12977-2:2001

Thermal solar systems and components - Custom built systems - Test methods

This European Prestandard applies to small and large custom built solar heating systems with liquid heat transfer medium for residential buildings and similar applications, and gives test methods for verification of the requirements specified in ENV 12977-1.
This Prestandard includes also a method for thermal performance characterization and system preformance prediction of small custom buil systems by means of component testing and system simulation.
Furthermore, the Prestandard contains methods for thermal performance prediction of large custom built systems.

Non prevista

00312008

ENV 12977-3:2001

Thermal solar systems and components - Custom built systems - Part 3: Performance characterisation of stores for solar heating systems

This Prestandard specifies test methods for the performance characterization of store which are intended for use in small custom built systems as specified in ENV 12977-1.
Stores tested according to this Prestandard are commonly used in solar hot water systems. However, also the thermal performance of all other thermal stores with water as storage medium (e.g. for heat pump systems) can be assessed according to this Prestandard.
The Prestandard applies to stores with a nominal volume between 50 and 3000 litres and without integrated oil or gas burner.

Non prevista

00312014

CEN/TS 12977-1:2010

Thermal solar systems and components - Custom built system - Part 1: General requirements for solar water heaters and combisystems

This document (prCEN/TS 12977 1) specifies requirements on durability, reliability and safety of small and large custom built solar heating and cooling systems with liquid heat transfer medium in the collector loop for residential buildings and similar applications. This document contains also requirements on the design process of large custom built systems.

Non prevista

00312015

CEN/TS 12977-2:2010

Thermal solar systems and components - Custom built systems - Part 2: Test methods for solar water heaters and combisystems

This document (prCEN/TS 12977 2:2008) applies to small and large custom built solar heating systems with liquid heat transfer medium for residential buildings and similar applications, and gives test methods for verification of the requirements specified in prCEN/TS 12977 1. This document includes also a method for thermal performance characterization and system performance prediction of small custom built systems by means of component testing and system simulation.

Non prevista

00312017

CEN/TS 12977-4:2010

Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores

This document specifies test methods for the performance characterization of stores which are intended for use in small custom built systems as specified in prCEN/TS 12977 1. Stores tested according to this document are commonly used in solar combisystems. However, also the thermal performance of all other thermal stores with water as storage medium can be assessed according to the test methods specified in this document. This document applies to combisstores with a nominal volume up to 3000 litres and without integrated burner. Remark: This standard is extensively based on references to prEN 12977-3.

Non prevista

00312018

CEN/TS 12977-5:2010

Thermal solar systems and components - Custom built systems - Part 5: Performance test methods for control equipment

This document (prCEN/TS 12977-5:2008) specifies performance test methods for control equipment. Furthermore this document contains requirements on accuracy, durability and reliability of control equipment. The tests described in prCEN/TS 12977-5 are limited to components delivered with or for the system by the final supplier.

Non prevista

00312010

EN 12975-2:2006

Thermal solar systems and components - Solar collectors - Part 2: Test methods

This European Standard specifies test methods for validating the durability, reliability and safety requirements for liquid heating collectors as specified in EN 12975-1. This standard also includes three test methods for the thermal performance characterisation for liquid heating collectors. It is not applicable to those collectors in which the thermal storage unit is an integral part of the collector to such an extent that the collection process cannot be separated from the storage process for the purpose of making measurements of these two processes. Collectors that are custom built (built in; e.g. roof integrated collectors that do not compose of factory made modules and are assembled directly on the place of installation) cannot be tested in their actual form for durability, reliability and thermal performance according to this standard.

Non prevista

00312011

EN 12976-2:2006

Thermal solar systems and components - Factory made systems - Part 2: Test methods

This European Standard specifies test methods for validating the requirements for Factory Made Thermal Solar Heating Systems as specified in EN 12976-1. The standard also includes two test methods for thermal performance characterization by means of whole system testing

Non prevista

00312012

EN 12976-1:2006

Thermal solar systems and components - Factory made systems - Part 1: General requirements

This European Standard specifies requirements on durability, reliability and safety for Factory Made thermal solar heating systems. The standard also includes provisions for evaluation of conformity to these requirements.The requirements in this standard apply to Factory Made solar systems as products. The installation of these systems itself is not considered, but requirements are given for the documentation for the installer and the user which is delivered with the system.

Non prevista

00312016

EN 12977-3:2008

Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores

This European Standard specifies test methods for the performance characterization of stores which are intended for use in small custom built systems as specified in prCEN/TS 12977-1. Stores tested according to this document are commonly used in solar hot water systems. However, also the thermal performance of all other thermal stores with water as storage medium can be assessed according to the test methods specified in this document. The document applies to stores with a nominal volume between 50 l and 3 000 l. This document does not apply to combistores. Performance test methods for solar combistores are specified in prCEN/TS 12977-4.

Non prevista

00312002

EN 12975-1:2000

Thermal solar systems and components - Solar collectors - Part 1: General requirements

This European standard specifies requirements on durability (including mechanical strength), reliability and safety for liquid heating solar collectors. It also includes provisions for evaluation of conformity to these requirements. It is not applicable to those collectors in which the thermal storage unit is an integral part of the collector to such an extent, that the collection process cannot be separated from the storage process for the purpose of making measurements of these two processes. It is not applicable to tracking concentrating solar collectors.

Non prevista

00312004

EN 12976-1:2000

Thermal solar systems and components. Factory made systems. Part 1: General requirements

This European Standard specifies requirements on durability, reliability and safety for Factory Made thermal solar heating systems. The standard also includes provisions for evaluation of conformity to these require-ments.The requirements in this standard apply to Factory Made solar systems as products.

Non prevista

00312003

EN 12975-2:2001

Thermal solar systems and components - Solar collectors - Parts 2: Test methods

This European Standard specifies test methods for validating the durability, reliability and safety requirements for liquid heating collectors as specified in EN 12975-1. This standard also includes three test methods for the thermal performance characterisation for liquid heating collectors. It is not applicable to those collectors in which the thermal storage unit is an integral part of the collector to such an extent that the collection process cannot be separated from the storage process for the purpose of making measurements of these two processes. It is not basically not applicable to tracking concentrating collectors, however thermal performance testing as given in clause 6.3 (quasi dynamic testing) is also applicable to most concentrating collector designs, from stationary non-imaging concentrators as CPCs to high concentrating tracking designs. Parts of the solar radiation measurement have to be adjusted in case of a tracking collector and in case a pyrheliometer is used to measure beam radiation. Collectors that are custom built (built in; e.g. roof integrated collectors that do not compose of factory made modules and are assembled directly on the place of installation) cannot be tested in their actual form for durability, reliability and thermal performance according to this standard. Instead, a module with the same structure as the ready collector may be tested. The module gross area shall be at least 2m2.

Non prevista

00312005

EN 12976-2:2000

Thermal solar systems and components - Factory made systems - Part 2: Test methods

scopo

Non prevista

00312009

EN 12975-1:2006

Thermal solar systems and components - Solar collectors - Part 1: General requirements

This European standard specifies requirements on durability (including mechanical strength), reliability and safety for liquid heating solar collectors. It also includes provisions for evaluation of conformity to these requirements. It is not applicable to those collectors in which the thermal storage unit is an integral part of the collector to such an extent, that the collection process cannot be separated from the storage process for the purpose of making measurements of these two processes. It is not applicable to tracking concentrating solar collectors.

Non prevista

00312024

UNI EN 12977-1:2012

Thermal solar systems and components - Custom built systems - Part 1: General requirements for solar water heaters and combisystems

This document specifies requirements on durability, reliability and safety of small and large custom built solar heating and cooling systems with liquid heat transfer medium in the collector loop for residential buildings and similar applications. This document contains also requirements on the design process of large custom built systems.

Non prevista

00312025

UNI EN 12977-2:2012

Thermal solar systems and components - Custom built systems - Part 2: Test methods for solar water heaters and combisystems

This document applies to small and large custom built solar heating systems with liquid heat transfer medium for residential buildings and similar applications, and gives test methods for verification of the requirements specified in CEN/TS 12977-1. This document includes also a method for thermal performance characterization and system performance prediction of small custom built systems by means of component testing and system simulation. Furthermore, this document contains methods for thermal performance characterization and system performance prediction of large custom built systems. This document applies to the following types of small custom built solar heating systems: - systems for domestic hot water preparation only; - systems for space heating only; - systems for domestic hot water preparation and space heating; - others (e. g. including cooling). This document applies to large custom built solar heating systems, primarily to solar preheat systems, with one or more storage vessels, heat exchangers, piping and automatic controls and with collector array(s) with forced circulation of fluid in the collector loop. This document does not apply to: - systems with a store medium other than water (e.g. phase-change materials); - thermosiphon systems; - integral collector-storage (ICS) systems.

Non prevista

00312026

UNI EN 12977-4:2012

Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores

This document specifies test methods for the performance characterization of stores which are intended for use in small custom built systems as specified in CEN/TS 12977-1. Stores tested according to this document are commonly used in solar combisystems. However, also the thermal performance of all other thermal stores with water as storage medium (e.g. for heat pump systems) can be assessed according to the test methods specified in this document. This document applies to combisstores with a nominal volume up to 3000 l and without integrated burner. Note: This document is extensively based on references to EN 12977 3:2008.

Non prevista

00312027

UNI EN 12977-5:2012

Thermal solar systems and components - Custom built systems - Part 5: Performance test methods for control equipment

This document specifies performance test methods for control equipment. Furthermore this document contains requirements on accuracy, durability and reliability of control equipment. The tests described in CEN/TS 12977-5 are limited to components delivered with or for the system by the final supplier. For the purposes of this document (CEN/TS 12977-5) controller and control equipment for solar heating systems and auxiliary heaters, if part of the system, are restricted to: a) Controllers as 1) system clocks, timers and counters, 2) differential thermostats, 3) multi-function controllers. b) Sensors as 1) temperature sensors, 2) irradiance sensors (for short wave radiation), 3) pressure sensors, 4) level sensors, 5) flow meters or 6) heat meters. c) Actuators as 1) pumps, 2) solenoid and motor valves or 3) relays. Furthermore combinations of controllers, sensors and actuators listed above. An additional objective of the procedures described in this document is to verify control algorithms and, together with the accuracy of sensors, to determine control parameters. In addition to verifying the functioning of a controller, its equipment and actuators, the determined parameters may be used for numerical system simulations. Typically electrical anodes are not part of the control equipment and are not controlled by the control equipment. However, because they are electrical appliance, electrical anodes are included in this document. This document is valid for control equipment of solar heating systems for the purpose of hot water preparation and/or space heating. If the solar system is connected to or part of a conventional heating system, the validity is extended to the entire system. In combination with the standards EN 12976-1, EN 12976-2 as well as CEN/TS 12977-1, CEN/TS 12977-2, EN 12977-3 and CEN/TS 12977-4 this document is valid for: [...]

Non prevista

00312029

EN ISO 9806:2013 (UNI EN ISO 9806:2014)

Solar energy - Solar thermal collectors - Test methods (ISO 9806:2013)

This European Standard specifies test methods for validating the durability, reliability and safety requirements for liquid heating collectors as specified in EN 12975-1. This standard also includes three test methods for the thermal performance characterization for liquid heating collectors. . It is not applicable to those collectors in which the thermal storage unit is an integral part of the collector to such an extend, that the collection process cannot be separated from the storage process for the purpose of making measurements of these two processes. It is basically applicable to tracking concentrating collectors, thermal performance testing is given in 6.3 (quasi dynamic testing) is also applicable to most concentrating collector designs, from stationary non-imaging concentrators as CPCs to high concentrating tracking designs. Parts of the solar radiation measurement should be adjusted in case of a tracking collector and in case a pyrheliometer is used to measure beam radiation. Collectors that are custom - built (built in; e.g. roof integrated collectors that do not compose of factory made modules and are assembled directly on the place of installation) cannot be tested in their actual form for durability, reliability and thermal performance according to this standard. Instead, a module with the same structure as the ready collector may be tested. The module gross area should be at least 2m2.The test is valid only for larger collectors, than the tested module.

Non prevista

00312031

UNI EN 12977-3:2012

Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores

-

Non prevista

00312035

UNI EN 12976-2:2017

Thermal solar systems and components - Factory made systems - Part 2: Test methods

-

Non prevista

00312030

EN 12975-1:2006+A1:2010

Thermal solar systems and components - Solar collectors - Part 1: General requirements

This European Standard specifies requirements on durability (including mechanical strength), reliability and safety for liquid heating solar collectors. It also includes provisions for evaluation of conformity to these requirements. It is not applicable to those collectors in which the thermal storage unit is an integral part of the collector to such an extent, that the collection process cannot be separated from the storage process for the purpose of making measurements of these two processes. It is basically applicable to concentrating collectors; thermal performance testing as given in EN 12975-2:2006, subclause 6.3. (quasi dynamic testing) is also applicable to most concentrating collector designs, from stationary non-imaging concentrators as CPCs to high concentrating tracking designs. Collectors that are custom-built (built in, roof integrated collectors that do not comprise factory made modules and are assembled directly on the place of installation) cannot be tested in their actual form for durability, reliability and thermal performance according to this standard. Instead, a module with the same structure as the ready collector is tested. The module gross area in the case of custom built collectors should be at least 2 m2. The test is valid only for larger collectors, than the tested module. For collectors the national and European Guidelines for Structural Planning and overhead glazing are not valid. Therefore this standard should be applied for the design of the static of the collector.

Non prevista